Lubrication and service
Man/hours
Injection pump:
0306 TANKS, LINES, FITTINGS
Screw, cam locating .............. 460 in.-lb (inch-
Tank, fuel
pounds).
(to remove cap, replenish fuel,
Screw, timing line cover ........ 15-20 in.-lb
replace cap.) .................................. 0.3
Rotor, transfer pump ............. 86-90 in.-lb
0303 FUEL FILTERS
Screw, head locking .............. 360 in.-lb
Filter assembly
Screw fuel line connector ...... 360 in.-lb
(to drain filters and replace
Screw head locating .............. 420 in.-lb
element.) .................................... 0.4
Plug, end plate ...................... 360 in.-lb
0311 ENGINE STARTING. AIDS
Screw, end plate .................... 25-30 in.-lb;
Starting aid, ether
Plug, end plate pipe
(to install and puncture ether
(tighten to seal only) ........ 360 in-lb maximum
capsule.) .................................... 0.1
Nut, torque screw .................. 25 in.-lb
05
COOLING SYSTEM
Screw, positioning ................. 25-30 in.-lb
0501 RADIATOR
Stud, guide ............................ 110-115 in.-lb
Radiator assembly
Nut, pivot shaft retainer ......... 20-25 in.-lb
(to drain and refill radiator.) ........ 0.4
Screw, adjusting lever............ 36-40 in.-lb
0504 WATER PUMP
retaining.
Pump assembly, water
Cap and filter assembly .. 240 in.-lb
(to clean lubrication fittings
1. Time Standards. Table 1 lists the number of man-
and lubricate) ............................ 0.1
hours required under normal conditions to perform the
06
ELECTRICAL SYSTEM
indicated maintenance and repair of the Jaw Crusher.
0603 STARTING MOTOR
The times listed are not intended to be rigid standards.
Starter assembly
Under adverse conditions, the operation will take
(to clean lubrication points and
considerably longer; but under ideal conditions with
lubricate.) ................................... 0.1
highly skilled mechanics, most of the operations can be
0612 BATTERIES
accomplished in considerably less time.
Batteries
(to remove cover and add water to
Table 1. Time Standards
the batteries.) ................................. 0.3
Lubrication and service
Man/hours
11
REAR AXLE
0122 ENGINE
1108 WALKING BEAMS
0100 ENGINE ASSEMBLY
Beams, walking
Engine, diesel
(to clean lubrication points and
(to drain crankcase and refill to
lubricate.) .................................. 0.2
proper level.) ............................... 0.7
12
BRAKES
1206 MECHANICAL BRAKE SYSTEM
0106
ENGINE LUBRICATION SYSTEM
Slack adjusters
Filter assembly, oil
(to clean lubrication points and
(to remove cover, discard element
lubricate.) .................................. 0.1
and gasket, clean filter body,
1208 AIR BRAKE SYSTEM
install new element and gasket,
Filters, air
replace cover.) .......................... 0.4
(to remove cover, remove filter,
Breather
clean and replace, drain moisture,
(to remove cap, clean, dry and
replace plug and cover.) ................. 0.4
replace.) .................................... 0.2
Reservoir, air
02
CLUTCH ASSEMBLY
(to open draincock and expel
0200 CLUTCH ASSEMBLY
moisture from tank.) ....................... 0.1
Clutch assembly
13
WHEELS
(to clean lubrication points and
1311 WHEEL ASSEMBLY
lubricate.) .................................. 0.1
Wheel assemblies
03
FUEL SYSTEM
(to remove wheel and bearings,
0304 AIR CLEANER
clean and lubricate bearings,
Air cleaner assembly
replace wheel.) ............... (each) 0.5
(to clean cup and replace filter
1313 TIRES, TUBES
element.) ................................... 0.3
Tires
(to check tire pressure and inflate
to proper pressure.) ............ (all) 0.4
5