TM 5-3820-233-35/2
1 Capscrew
31
Nut
61
Nut
2 Bevel washer
82
Liner
62
Brace
3 Lockwasher
38
Liner
63
Brace
4 Nut
34
Liner
64
Capscrew
5 Dust shield
86
Liner
66
Capscrew
6 Dust shield
36
Capscrew
66
Bolt
7 Cover
87
Washer
67
Lockwasher
8 Bolt
38
Lockwasher
68
Nut
9 Lockwasher
39
Nut
69
Bolt
10 Nut
40
Capscrew
70
Lockwasher
11 Liner
41
Washer
71
Nut
12 Capscrew
42
Lockwasher
72
Pan
13 Lockwasher
43
Nut
73
Liner
14 Plate
44
Chute
74
Spacer
16 Bolt
45
Capscrew
75
Spacer
16 Bolt
46
Lockwasher
76
Box
17 Washer
47
Nut
77
Screw
18 Nut
48
Pad
78
Plate
19 Clamp (RH)
49
Leaf spring
79
Straight edge
20 Clamp (LH)
50
Cotter pin
80
Capscrew
21 Clamp (RH)
61
Seat (RH)
81
Capscrew
22 Clamp (LH)
62
Seat (LH)
82
Lockwasher
2S C3mp(RH)
53
Jack
93
Nut
24 Clamp (LH)
64
Nut
84
Capscrew
25 Clamp (RH)
66
Nut
85
Washer
26 Clamp (LH)
56
Spring
86
Lockwasher
27 Channel
57
Screw
87
Nut
28 Frame
58
Plate
88
Brace
29 Bolt
69
Capscrew
89
Brace
30 Lockwasher
60
Lockwasher
90
Base
Figure 40-2--Continued
Note.
(r) Install end plates (17, fig. 40-3),
Use the short mounting tool shown on
lockwashers (16), capscrews (15), and locking wire (14).
(s) Install gear case cover (9) using a
mounting tool shown on figure 40-8
new gasket (9). Tighten capscrews (5) securely. Install
when installing the driven shaft
plug (1).
bearing.
(t) Refer to the Operator's Manual for
(b) Install end plate (17, fig. 40-3) to
timing gear lubrication instructions.
driven shaft (51). Install end cap (13).
(3) Driven Shaft Bearing Removal.
(c) Refer to the Operator's Manual for
(a) Remove end cap (fig. 40-5).
bearing lubrication instructions.
(b) Remove end plate (17, fig. 40-3)
(d) Refer to step a(2) above, and repeat
from driven shaft (51).
instructions (n) through (t).
(c) Remove the driven shaft bearing in
b. Bearing Removal (Gear Side).
the same manner as the drive shaft bearing. Repeat
(1) Drain lubricant from gear case.
steps (d) through (h) under step a (1) above.
(2) Remove cover (8, fig. 40-3), gasket (9),
Note.
and end plates (17).
Use shorter bolts than those shown on
(3) Remove both timing gears using the
figure to assemble plate to puller ring.
Special Tools shown on figure 40-7. Turn driven shaft
until keyway is at bottom of shaft. Hold shaft in this
position while removing gear. This will prevent the shaft
(4) Driven Shaft Bearing Installation.
from "swinging free" when gear is removed. Repeat
(a) Refer to step a(2) above, and repeat -
procedure for remaining gear.
instructions (a) through (l).
4-29
